3D-printed electronics could give engineers a way to integrate electrical functions directly into parts rather than designing every circuit as a separate, flat assembly. In fused filament fabrication (FFF), that means combining insulating thermoplastic with conductive filament to build traces and components in three dimensions. The approach is not a substitute for every conventional circuit process, but it can support custom geometries, embedded components and integrated prototypes.
Research published in 2017 demonstrated this approach using a dual-material FFF printer and conductive thermoplastic filaments. Printed resistors, capacitors and inductors were combined into a functional high-pass filter, while a separate demonstration used printed traces to connect an embedded LED. The results also highlight a practical engineering constraint: conductive filament has measurable resistance, so material properties and geometry must be part of the circuit design.
Why conductive filament changes the design options
Conventional FFF printers are primarily designed to deposit insulating plastics. Conductive filaments add electrical functionality, allowing a printer to form traces alongside structural and dielectric features. Unlike processes that print onto a surface or require a post-printing step such as metallization, this method can create freestanding or embedded conductive features as part of the printed object.
The study compared filaments using carbon black, graphene and copper-based conductive fillers. Their measured resistivities were approximately 12, 0.78 and 0.014 Ω·cm, respectively. These values differ substantially from the very low resistance of a copper PCB trace. A printed conductor therefore cannot automatically be treated as an ideal interconnect: its resistance may influence voltage drops and circuit behavior.
Material selection also affects mechanical durability. The carbon-based filaments fractured during the reported bending tests, while the copper-based filament survived 500 cycles of bending through 180 degrees. Its resistance roughly doubled during the first few cycles, then stabilized. This finding illustrates why electrical characterization should be considered alongside mechanical requirements when selecting a filament for a flexible or repeatedly handled part.
3D-printed electronics: designing around geometry
For a printed trace, resistance depends on its material resistivity, length and cross-sectional area. In simplified form, resistance increases with length and resistivity, and decreases as cross-sectional area increases. This relationship means a trace can serve as an intentional resistive element if its dimensions and material are controlled.
In the reported work, changing the cross-sectional area of 50 mm-long traces produced resistors spanning roughly 10 Ω to 10 kΩ. The researchers found a linear relationship between resistance and inverse cross-sectional area, consistent with the expected resistivity model. For design teams, the practical implication is that trace dimensions are not only a routing decision; they can also determine component behavior.
Printed inductors and capacitors likewise depend on geometry and material. Spiral inductors were made with different turn counts, with an insulating PLA structure enabling the coil’s inner connection to cross over other parts of the winding. Measured inductance tracked a conventional geometric approximation, although the measurements showed a systematic offset.
Parallel-plate capacitors were built by alternating conductive layers and insulating separators. Capacitance increased with the number of stacked capacitor layers. It could also be influenced by plate overlap, separator thickness and the dielectric material. The study reported higher capacitance for bronze-filled PLA than for black-pigmented PLA, consistent with the different dielectric properties measured for the two materials.
From individual components to a working circuit
To test whether the printed elements could function together, the researchers fabricated a dual-material high-pass filter using conductive traces, a 60 pF capacitor and a 2.2 µH inductor. Its measured cutoff frequency was approximately 7 MHz, and the filter attenuated lower-frequency signals. The result showed that printed components could be assembled into a circuit with behavior comparable to a conventional first-order passive high-pass filter.
The conductive filament also enabled a printed spiral coil to receive power from a commercial wireless phone charger and light an LED. This demonstration depended on the copper-based filament’s comparatively low impedance. Its impedance was similar to that of a copper PCB trace at frequencies around and above 1 MHz, according to the reported measurements. That comparison is frequency-specific; it does not mean the printed material behaves like copper across all operating conditions.
Dual-material printing and embedded components
Combining conductive and insulating filaments requires reliable material switching. If residue from one material contaminates the other, a conductive path may be interrupted or unintended connections may form. The study addressed this challenge with a dual-extrusion printer using retractable hotends, which lift the inactive nozzle away from the print. The printer was based on an open-source design and had a reported parts cost below $1,000 at the time of the work.
Dual-material FFF can also connect conventional electronic components to printed traces. In the embedded LED demonstration, printing paused so the component could be placed in a cavity. Printing then resumed, depositing conductive filament over the LED contacts. This approach allows standard surface-mount components to be incorporated where a printed component is unsuitable or where an existing part is required.
For integrators and product-development teams, these demonstrations point to several design considerations:
- Characterize the material: Measure resistance and frequency-dependent impedance rather than assuming a printed trace is equivalent to metal wiring.
- Use geometry deliberately: Trace length and cross-section affect resistance; coil layout and layer spacing influence inductance and capacitance.
- Plan material transitions: Nozzle retraction and print sequencing can help reduce cross-contamination between conductive and insulating filaments.
- Allow for conventional parts: Pausing a print to place a component provides a route to hybrid assemblies that combine printed structures with standard electronics.
Practical implications for industrial design
FFF-based electronics offer a way to explore custom, three-dimensional circuit layouts and integrate electrical features into printed structures. The demonstrated capabilities include resistors, capacitors, inductors, a high-pass filter, a wireless power receiver coil and an embedded LED connection. At the same time, the measured resistivity and mechanical behavior show that material limits must inform circuit architecture and application requirements.
For industrial automation engineers and system integrators, the most useful takeaway is that conductive thermoplastic is both a manufacturing material and an electrical design variable. Successful applications depend on matching its properties to the task, controlling dual-material deposition and validating the finished circuit. This makes the approach especially relevant to prototyping and specialized integrated parts, where geometric flexibility and component integration matter alongside electrical performance.
Access Official Technical PDF