A PEM fuel cell control system must coordinate reactant supply, stack monitoring, operator interaction, and protective actions. In a laboratory test setup, these functions help operators follow defined operating parameters while responding to conditions that could threaten the stack or make operation unsafe. A control architecture combining a programmable logic controller (PLC), a human-machine interface (HMI), sensors, valves, and a documented operating procedure provides a practical framework for that work.
The system described here was developed for laboratory-scale testing, not commercial fuel cell service. Its design illustrates how control and protection functions can be brought together around a proton exchange membrane fuel cell (PEMFC) stack.
Why PEM fuel cell control requires careful coordination
A PEMFC converts hydrogen and oxygen into electrical energy through electrochemical reactions, producing water and heat as by-products. Its solid polymer electrolyte conducts protons between the electrodes, while catalysts support the electrode reactions. PEMFCs operate at relatively low temperatures and can start quickly, but their operation depends on suitable reactant conditions. The source also notes that the catalyst is costly and sensitive to carbon monoxide, making fuel quality a relevant consideration.
For the test system, control design began by identifying the process variables to monitor or manage. These included stack temperature, hydrogen inlet and outlet pressure, stack voltage and current, battery voltage, cooling-air temperature, airflow, and purge timing. Hydrogen pressure is particularly important: insufficient supply can contribute to fuel starvation, while inappropriate pressure may damage the stack.
PEM fuel cell control system architecture
The prototype brought together three main subsystems: the control system, the reactant modules, and the fuel cell stack. A PLC handled control logic, while the HMI presented operating information and allowed the operator to interact with the system. Sensors and actuators connected the process to those control and display functions.
The design used an Outseal PLC board and an Autonics LP-S070 logic panel. The PLC uses ladder-diagram programming and a 24 V DC supply. The HMI includes a touchscreen, data-logging capability, and communication interfaces. The PLC and HMI communicated using Modbus RTU over a serial connection. The controller arrangement could also use master and slave PLC modules to expand the available inputs and outputs.
In this kind of setup, the HMI is more than a display. It gives operators a place to check process readings, see component status, adjust designated settings, and carry out calibration or testing tasks. A deliberately straightforward screen layout can help reduce confusion during operation. The project used three screen types:
- Main screen: Displayed readings and pilot-light indicators showing component status.
- Parameter screen: Provided settings such as purge time, stack temperature, and voltage-drop parameters.
- Calibration and test screen: Supported calibration and checks of regulating relay operation.
Monitoring, purging, and startup sequence
During startup, the dilution fan supplies air to the cathode, and the hydrogen supply valves open. The stack voltage then rises toward its open-circuit voltage. An initial anode purge introduces fresh hydrogen into the stack. Once the system reaches the required operating state, the stack can be connected to a dummy load or an electronic load for testing.
Temperature and pressure readings, along with voltage, current, and component status, give the operator information needed to assess the test. A thermistor monitors stack temperature. The described startup logic includes a shutdown at 78°C, while the operating instructions state that the module temperature must not exceed 75°C. These are distinct limits in the described procedure and should be treated as specified by the applicable system configuration rather than assumed to be interchangeable.
Purging is used to clear used gases from the stack and maintain conditions for operation. The design makes purge timing variable, allowing it to be set as a control parameter. Hydrogen inlet pressure is regulated through a solenoid valve, with outlet purging also managed by the control logic.
Safety interlocks and emergency shutdown
Protective functions are essential because the system uses hydrogen and operates an electrochemical stack. Before testing, the procedure calls for checking the system for gas leaks and confirming that operating parameters are within the required conditions. Hydrogen from a cylinder is supplied through a pressure regulator, and the control panel is used to observe process readings during operation.
The emergency sequence described for a stack voltage drop closes the fuel inlet and disconnects the load relay. The purge valve remains open and the blower remains on as part of the response intended to protect the stack and reduce its temperature. This sequence demonstrates how a shutdown should define not only what is stopped, but also which actions continue after the fault condition.
Documented operating procedures complement automatic control. An SOP helps operators follow a consistent sequence, verify conditions before admitting hydrogen, and avoid actions that could damage equipment or create hazards. It should reflect the actual configuration and setpoints of the installed system.
Practical implications for test-system design
For engineers and integrators, the central lesson is to design the operator interface, control logic, instrumentation, and protection response as connected parts of one system. The HMI should make essential readings and statuses visible; the PLC should execute defined operating and shutdown logic; and sensors and actuators should support the required monitoring and response.
Communication settings also matter during commissioning. The described implementation used Modbus RTU over RS232 and required matching communication settings between the PLC and HMI. Configuration details such as baud rate and programming procedure should be verified for the equipment being commissioned.
A well-structured PEM fuel cell control system can make laboratory testing easier to operate and more informative while providing a defined response to abnormal conditions. For practical deployment, teams should validate setpoints, interlocks, communication, and SOPs against the specific stack and test configuration. Clear monitoring and carefully specified protective actions are fundamental to operating and testing the system responsibly.
Access Official Technical PDF