Small wearable sensors can support continuous health monitoring and other data-driven applications, but their power supply can complicate device design. Batteries add size and weight, while cables can limit movement. A proposed NFC wireless power transfer system offers another approach: use a mobile device to supply power to a sensor antenna positioned on the fingertip. Simulation and measurement results indicate that the design can deliver more than the 1.0 mW power target set for the sensor application.
Why power is a design constraint for wearable sensors
Wearable devices are useful when they can remain comfortable during everyday activity. Sensors intended to monitor vital signs or finger movement may need to be worn regularly, making overall size and the burden of charging important design considerations. A battery can contribute to device bulk, and a wired power connection is not well suited to a device that moves with the user.
Wireless power transfer (WPT) can reduce reliance on batteries and cables by delivering energy across a short distance. The system discussed here is designed around a specific interaction: the user places a finger against the back of a mobile device, allowing a transmitter in the device to couple power to a receiving antenna on the fingertip. The same fingertip sensor concept is intended to support vital-data monitoring and finger-motion sensing.
How the NFC wireless power transfer system works
The proposed link operates at 13.56 MHz, the frequency used for NFC. It uses magnetic resonance between transmitting and receiving square spiral coils. The transmitter is associated with the mobile device, while the compact receiver is sized for placement on an index finger. The receiving antenna measures 10.0 by 14.0 mm.
The design assumes that the finger is positioned on the back of the device, with the transmitting and receiving antennas aligned along their center axis. Neither antenna is in direct contact with the body. The modeled arrangement includes an air gap of 1.0 mm between the fingertip phantom and receiving antenna, representing space for sensor and circuit components, and 3.0 mm between the phantom and transmitting antenna, representing the device cover or other intervening elements.
A saline phantom represents the electrical properties of human tissue. Its relative permittivity is 78 and its conductivity is 0.4 S/m. The design uses 13.56 MHz because, as described in the study, the magnetic field at this frequency is hardly affected by the human body. The system is assessed against a receiving-power target of 1.0 mW. The paper notes that the NFC Forum’s Wireless Charging Specification enables NFC antennas in compatible devices to charge low-power IoT devices.
Antenna matching and evaluation
Both antennas use square spiral coils on FR4 substrates and include matching circuits designed for a 50-ohm match. Matching is important in this design because the antennas are small relative to the wavelength at NFC frequencies. The transmitting antenna follows an NFC antenna design guide, while the receiving antenna is constrained by its fingertip location.
The team compared frequency-domain simulation with measurements of fabricated antennas. Measurements were taken with the antennas in air and with the receiving antenna positioned on the phantom. The antenna response showed little difference between the air and phantom measurement conditions. The reported reflection results also indicate that both antennas can be used at the intended 13.56 MHz operating frequency.
What the power results show
At a transmitting power of 1.0 W, the simulated transmission coefficient at 13.56 MHz was -7.4 dB, corresponding to a reported receiving power of 182.0 mW. The measurement transmission coefficient was -16.4 dB, with a reported receiving power of 22.9 mW. Although the measured result is lower than the simulation, it remains above the study’s 1.0 mW requirement for the IoT sensor.
The simulation also assessed how antenna alignment affects the area in which the receiver can obtain at least 1.0 mW. At the 1.0 W transmitting-power condition, that area extended to within ±28 mm in the x direction and ±25 mm in the y direction from the antennas’ center axis. These figures describe the evaluated configuration, rather than a general performance guarantee for other devices or placements.
The difference between simulated and measured transmission efficiency is an important engineering consideration. The study reports that the phantom and coaxial-cable length did not account for the difference, and identifies conductor loss as a probable contributor. The simulation did not include conductor loss, while the fabricated antenna measurements reflect the realized hardware.
Implications for wearable and IoT design
The results demonstrate the feasibility of transferring enough power for the stated sensor requirement in the tested arrangement. For device designers and system integrators, the work highlights several practical factors to account for:
- Placement: The transfer link depends on the relationship between transmitter and receiver position.
- Antenna size: A fingertip-mounted receiver has limited area, making coil design and matching central to the system.
- Real-world losses: Measured hardware may deliver less power than an idealized simulation, so conductor losses and implementation details matter.
- Mechanical spacing: Device covers and sensor components create gaps that should be represented in the design and evaluation.
The work does not establish performance across all mobile devices, sensor loads, or operating conditions. It does, however, provide a measured example of an NFC-based power link designed around a small fingertip receiver and a defined power target.
Conclusion
NFC wireless power transfer could help address the battery and cabling constraints of compact wearable sensors. In this 13.56 MHz fingertip system, measurements showed 22.9 mW of receiving power at 1.0 W transmission, exceeding the 1.0 mW target despite lower efficiency than the simulation predicted. Further development identified by the authors includes optimizing the receiving antenna with thin, flexible materials. For engineers evaluating similar designs, the key takeaway is to validate the complete antenna assembly and its losses under representative spacing and placement conditions.
Access Official Technical PDF