📘 Resource Overview & Documentation Details

You are viewing the technical directory listing for Mycelium-Clay 3D Printing: A New Structural Approach. This engineering resource is curated under our Digital manufacturing division to support automation specialists, control systems engineers, and manufacturing technicians looking for verified reference materials.

🔍 Contextual Abstract & Technical Scope

Share Summary:LinkedInEmail

Mycelium-clay 3D printing combines paste-based digital fabrication with the growth of fungal fibres to create structural components with material properties shaped by both toolpath and biology. In the MyCera research project, clay elements were printed, inoculated with mycelium, and assembled while the organism was still growing. Tests found higher tensile strength in grown samples than in comparable samples without mycelium, while a design study demonstrated how growth could connect separate elements.

The approach is relevant to engineers and designers exploring bio-based building materials, but it remains experimental. Its value lies not in a ready-made substitute for conventional construction products, but in showing how manufacturing processes and material behavior might be coordinated at different scales.

Why combine clay fabrication and mycelial growth?

Clay is widely available, but its digital fabrication methods have developed less extensively than those used for concrete and steel. Paste extrusion can produce geometries that conventional ceramic processes may not readily achieve, yet printed clay parts still face challenges around strength, joining, and manufacturing consistency.

Mycelium—the network of fine, branching hyphae that forms the vegetative part of a fungus—offers a different manufacturing mechanism. It can grow through suitable organic substrates and bind material as it develops. In MyCera, the researchers combined clay and sawdust with mycelium, using digital fabrication to control the initial geometry and biological growth to create fibre connections within and between components.

This pairing also separates functions across the structure. The project developed fired clay bars intended primarily to carry compressive loads and unfired, mycelium-rich nodes intended to accommodate tensile and torsional loads. These roles describe the design strategy, not a general performance rating for clay-mycelium components.

How the mycelium-clay 3D printing workflow works

The team tested clay mixtures with several potential substrates before selecting sawdust. The reported printing mixture used a clay-to-sawdust weight ratio of 7:1, with water added to give the paste a printable consistency. Sawdust particles were sieved to less than 2 mm to reduce the risk of blocking the printer nozzle. Keeping water content low was important: excess water can make overhanging forms harder to print and increase drying time and shrinkage concerns.

A customized clay printer and a workflow connecting Rhino 3D geometry to machine instructions supported the fabrication process. Toolpaths were designed for the intended part:

  • Spiral paths supported continuous extrusion for cylindrical objects, avoiding repeated starts and stops between layers.
  • Alternating layer directions created crossed paths in solid elements to provide a more stable printed structure.
  • Variable extrusion flow and speed allowed wall thickness to change along a printed line.
  • Path simulation helped identify potential collisions between the printer head and the evolving geometry.

After printing, parts were sterilized and inoculated rather than mixing the spawn into the paste before extrusion. This approach avoided the more complicated task of maintaining sterile conditions throughout printing. Solid parts were inoculated at the surface, while hollow forms could be filled with spawn.

What the strength tests showed

The researchers compared samples with and without mycelial growth in two tensile tests. In the first, force was applied along the extrusion axis. After 14 days of growth, samples with mycelium had an average maximum tensile force of 204.28 N, compared with 122.60 N for samples without growth. The reported increase in average maximum tensile strength was 66.62%.

A second test examined the connection between printed layers. Grown samples recorded an average maximum tensile force of 110.90 N, compared with 83.80 N for samples without mycelium—a reported increase of 32.34%. In these tests, the researchers did not observe a notable change in elongation behavior. These results apply to the tested specimens and conditions; they do not establish structural design values for buildings or long-term performance.

Mycelium was also observed growing through a printed clay wall up to 9.5 mm thick. The researchers proposed that growth helps form fibre reinforcement and improve connections between layers. Further investigation, including examination of internal porosity at a finer scale, was identified as necessary.

Joining elements through biological growth

The design study brought fired bars and growing mycelium-rich nodes together in a combined structure. After the bars had been inoculated and allowed to grow, they were dried and fired. Firing removed the organic material, leaving a branching internal pore structure in the ceramic. The nodes remained unfired so that the mycelium could continue growing.

When assembled, the hyphal network expanded across contact points and connected adjacent parts. This bio-welding helped bridge gaps and accommodate uneven contact between surfaces—functions that the researchers compared with the gap-filling role of mortar. The completed assembly was then dried under atmospheric conditions. In this concept, the connection depends on growth across the interface, rather than relying solely on a separate mechanical fastener or conventional binder.

Engineering considerations and next steps

The findings suggest several possibilities for digital fabrication and material-aware design: printed geometry can be tailored to part function, while growth can be treated as an additional design parameter. However, translating the concept into industrial or building applications requires more evidence and process development.

  • Sterile production: Preventing contamination is a central manufacturing challenge in the reported workflow.
  • Durability: Long-term behavior under atmospheric exposure remains unresolved.
  • Validation: The tested tensile results need to be understood within the limits of the specimen scale and experimental conditions.
  • Process development: Proposed future work includes multi-nozzle fabrication, closer examination of internal structure, and incorporating growth behavior into 3D modeling tools.

The researchers also identified comparison with other reinforcing fibres and investigation of protective coatings as future topics, rather than established solutions.

Conclusion

Mycelium-clay 3D printing demonstrates how digital toolpaths and biological growth can work together to produce reinforced parts and connect elements. The reported increases in tensile performance and the growth-based assembly are promising research outcomes, not proof of readiness for general construction use. For automation and manufacturing teams, the practical takeaway is a new way to think about process design: control the printed geometry first, then account for how a living material may alter reinforcement and connections over time. Sterility, durability, repeatability, and structural validation remain essential steps before broader application.

Access Official Technical PDF