Mobile robot kinematics describes how wheel motion produces a robot’s movement through its environment. Unlike a fixed-base manipulator, a wheeled robot is not anchored to one location, and its movement is constrained by the way its wheels roll and slide against the ground. For engineers and integrators, understanding these relationships is essential to designing a workable drive configuration, estimating position and selecting an appropriate motion-control approach.
A key distinction is that wheel encoder readings do not, by themselves, identify a unique robot pose. A mobile robot’s position must be estimated by integrating motion over time, so the result depends on the path taken and can accumulate error. Kinematic models help describe this motion, but they must account for the constraints imposed at the wheel-ground contact points.
How mobile robot kinematics differs from manipulator kinematics
A conventional robot arm is fixed to its base and typically consists of a chain of actuated links. Its joint positions can be related to the position of its end effector. A mobile robot instead changes its pose by moving across a surface. Its wheels impose rolling and sliding constraints that limit which instantaneous motions are possible.
Both types of robots use forward and inverse kinematics. In mobile robotics, however, non-holonomic constraints make velocity relationships especially important. Rather than directly mapping a set of joint positions to a final location, a differential kinematic model relates the robot’s linear and angular velocities to the change in its pose.
Why non-holonomic constraints matter
A system is non-holonomic when its motion constraints cannot be reduced to a direct relationship between position coordinates alone. For a wheeled robot, knowing how far each wheel has turned is not always enough to determine the final position. The sequence and timing of the movement also matter.
For example, two motion sequences can involve the same total wheel travel yet leave a robot in different locations. This is why an encoder-based estimate must account for motion over time, rather than treating wheel distances as a direct measurement of final pose. The limitation also affects control: a robot may be unable to move directly toward a target in every direction, even if that target is within reach.
Wheel configuration is a system-level design choice
Wheel arrangement affects stability, mobility, control complexity and odometry. A three-wheel vehicle can be stable when its center of gravity lies within the triangle formed by the wheel-ground contact points. Adding more wheels can improve stability, but configurations with four or more wheels can become hyperstatic. Such arrangements require a flexible suspension system to accommodate uneven contact with the ground.
Wheel selection also involves trade-offs. Larger wheels can pass over higher obstacles, but require higher torque or gearbox reduction. Many common wheel arrangements are non-holonomic and therefore demand careful control. Combining steering and drive actuation at one wheel can make the mechanical design more complex and introduce additional errors into odometry.
These trade-offs become more pronounced on rough terrain. Articulated suspensions allow wheels to adapt passively to terrain changes. One six-wheel arrangement uses two bogies on each side, a fixed rear wheel and a spring-suspended front wheel. The arrangement described in the source is intended to remain stable on rough ground and overcome obstacles up to twice its wheel diameter. More broadly, obstacle handling may rely on friction, changes in center-of-gravity position or suspension mechanisms with passive or active joints.
Motion control: open loop and feedback approaches
A kinematic controller aims to follow a trajectory defined by position or velocity over time. This is challenging because mobile robots are typically non-holonomic, and their motion involves multiple interacting variables. Kinematic controllers also generally do not account for the full dynamics of the robot.
Open-loop trajectory control
In open-loop control, a path is planned in advance and divided into motion segments, such as straight lines and circular arcs. More complex paths can use constructions such as Dubins or Reeds-Shepp paths, or combine lines, circles and clothoids. The controller then sends commands based on this predefined trajectory.
The approach places significant demands on planning. A feasible trajectory must respect the robot’s velocity and acceleration limits, and precomputed paths may not be smooth in acceleration or jerk. Since the plan does not adapt to changes in the environment, it cannot correct the trajectory in response to new conditions during execution.
Closed-loop feedback control
Feedback control uses the difference between the robot’s current state and its target state to calculate control commands. In a state-feedback approach, a control law maps position and orientation errors to linear and angular velocity commands. The objective is to drive those errors toward zero as the robot moves.
For a differential-drive robot, the kinematic model relates its forward velocity and angular velocity to changes in position and heading. A position controller can express the robot’s relationship to a goal in terms of distance and angles. This provides a way to generate motion commands that guide the robot toward the target while respecting its movement constraints.
There are practical details to handle. A polar-coordinate transformation used for position control is not defined when the robot is exactly at the goal, so the controller should stop when it is very close. The robot’s orientation relative to the goal also determines whether it approaches facing forward or backward. A control law can maintain a consistent direction of travel during a parking maneuver rather than switching direction partway through.
Practical implications for robot projects
Mobile robot kinematics connects mechanical design with localization and control. Wheel layout and suspension determine how the platform can move; wheel constraints shape the motion model; and that model informs odometry and trajectory tracking. An error or oversimplification at any stage can lead to a mismatch between the commanded movement and the estimated pose.
When evaluating a mobile robot design or control strategy, teams should consider:
- Ground contact and stability: Check how wheel placement and center-of-gravity location affect support.
- Terrain and obstacles: Match wheel size and suspension to the surfaces the platform must traverse.
- Motion constraints: Account for whether the configuration can move laterally or must maneuver through forward and rotational motion.
- Position estimation: Treat encoder-based pose as an estimate that develops over time, not a direct measurement of location.
- Control strategy: Choose between preplanned motion and feedback-based correction in light of trajectory feasibility and changing conditions.
The practical lesson is that reliable mobile-robot operation depends on treating the wheels, chassis, motion model and controller as parts of one system. A clear understanding of mobile robot kinematics helps teams select appropriate hardware, interpret odometry limits and develop motion-control strategies that reflect what the robot can physically do.
Access Official Technical PDF