📘 Resource Overview & Documentation Details

You are viewing the technical directory listing for Closed-Loop Process Control in Glass Manufacturing. This engineering resource is curated under our Smart Sensors division to support automation specialists, control systems engineers, and manufacturing technicians looking for verified reference materials.

🔍 Contextual Abstract & Technical Scope

Share Summary:LinkedInEmail

In glass container production, process conditions can shift during a run and after a job change. Operators need reliable information about what is happening at the forming machine, along with practical ways to correct deviations. Smart sensors and closed-loop process control address both needs by measuring production conditions and using that information to adjust machine settings automatically.

Integrated systems can monitor containers, regulate pressing and cooling, and help maintain consistent weight and conveyor spacing. Their value is not limited to automatic adjustments: continuous data can also help teams identify defects earlier, investigate root causes, and reduce the need for routine manual intervention.

How closed-loop process control supports forming

A closed loop uses measured process data to compare actual conditions with a target, then applies a correction within defined operating limits. In press-and-blow production, for example, Plunger Up Control works with Plunger Process Control to make the pressing process more stable. It can also adjust up to three pressure steps during pressing, an operation that can be difficult to manage manually for certain articles.

The system has also been used to reduce start-up time after a job change. That matters because a changeover requires production teams to establish suitable conditions for a new job while managing the transition back to stable operation. Automating selected adjustments can help make that process more consistent.

Forming process monitoring with smart sensors

FlexRadar monitors containers passing its cameras, providing ongoing visibility into the forming process. It can reject ware that is down or stuck and detect critical defects, including birdswing, thin spots, and leaners. It also gathers data about glass distribution and intensity for further process assessment.

This monitoring acts as a pre-filter for cold-end inspection. By identifying certain defects earlier in the production chain, the system can support faster investigation of their causes and prevent some nonconforming containers from continuing downstream. Its role is therefore both operational and diagnostic: it can respond to defined process limits while collecting information that helps teams look for patterns.

Continuous monitoring is particularly relevant when forming specialists and operators are not directly watching the line. Sensor data can maintain a view of production conditions beyond the periods when staff are positioned at the machine. That visibility can also support future automation development, provided that measurements and control actions are integrated appropriately into the process.

Automatic weight control and glass use

FlexRadar’s weight-control function uses radiated energy measurements from containers and correlates them with the actual glass mass recorded through periodic weighing. With an interface to the tube, the control can automatically adjust tube settings to hold weight at the selected setpoint. The system description gives a control range of down to ±0.5%.

Weight variation can otherwise lead manufacturers to set targets higher than the ideal value as a margin against underweight production. Automatic control may help reduce that variation and allow teams to reconsider the setpoint, subject to their quality requirements and process validation. The source describes a potential saving example in which reducing the setpoint by 2 g corresponds to €200,000 for a production line, using an annual price per gram of €100,000. This is an example based on those stated assumptions, not a universal saving estimate.

Keeping bottle spacing consistent

Uneven ware spacing on a conveyor can complicate downstream handling and inspection. FlexIS Bottle Spacing Control uses bottle-position deviations measured by FlexRadar to calculate corrections to each section’s push-out angle. The available adjustments are constrained by limits calculated from the control parameters for that section.

The control also coordinates events associated with push-out angle changes, such as pocket air. Because it is integrated with FlexIS, operators can change FlexPusher parameters or conveyor offset while the loop is running. Rather than opposing those inputs, the system continues to distribute ware evenly within its configured operating limits.

Gob loading and blank mould cooling

Gob loading is an important factor to consider when investigating forming defects. Measurements of other conditions, such as temperature, are more useful when loading-related problems are also understood; otherwise, an apparent response to one variable may obscure the underlying issue. As production relies less on direct human interaction, sensors such as BlankRadar can help provide information about the process and support existing or future closed-loop controls.

FlexIS Blank Cooling Control works with BlankRadar or TCS to maintain blank mould temperatures within a tighter band than manual adjustment. This can reduce the need for operators to continually monitor and adjust individual cavity cooling. The benefit is especially relevant on AIS and BIS machines with individual cavity cooling, where a section in triple-gob production can have up to six cooling valves.

Temperature control can also assist at the start of a production run. The loop can maintain more constant blank mould conditions while the desired glass temperature and feeder or forehearth conditions are still stabilizing. A similar closed-loop approach is available for plunger temperatures through FlexIS Plunger Cooling Control. The blank cooling system can be configured for different machine types.

Practical implications for plant teams

For engineers and operations leaders, integrated sensor and control systems offer a way to connect process visibility with targeted corrective action. The functions described address different parts of production—pressing, inspection, weight, spacing, gob loading, and mould temperature—but share a common requirement: dependable measurements and control limits suited to the machine and article.

  • Use monitoring data for diagnosis: Defect detection and process measurements can help teams investigate root causes rather than relying only on downstream inspection.
  • Define appropriate targets and limits: Automatic control should operate against setpoints and boundaries aligned with production and quality requirements.
  • Keep operators in the loop: Integration that accommodates operator adjustments can support production flexibility while maintaining the intended control objective.

In practice, closed-loop process control is most useful when it combines continuous sensing, carefully bounded adjustments, and accessible process information. For glass manufacturers, that combination can support steadier forming conditions, earlier identification of problems, and less dependence on repetitive manual adjustment—while leaving teams better positioned to focus on process improvement and production priorities.

Access Official Technical PDF