Soil moisture smart sensors help engineers and field teams monitor water content in soil over time. Designed for smart sensor-compatible HOBO data loggers, these probes combine an ECH2O dielectric measurement probe with an adapter that stores sensor conversion parameters. The logger can therefore report volumetric water content directly, without requiring users to program conversion settings.
Reliable data depends on more than the sensor itself. Probe selection, soil contact, installation depth, environmental conditions, and calibration all affect how readings should be interpreted. Understanding these factors helps teams build monitoring deployments that produce useful and consistent measurements.
How soil moisture smart sensors measure water content
The sensor measures the soil’s dielectric constant, an electrical property that changes with the amount of water present. Because water has a much higher dielectric constant than air or soil minerals, the measurement can be used to estimate volumetric water content (VWC).
The sensor reports VWC in cubic meters of water per cubic meter of soil (m³/m³). As a general operating guide, readings from 0 to 0.1 m³/m³ correspond to oven-dry through dry soil, while readings of 0.3 m³/m³ or higher normally indicate wet to saturated soil. These interpretations are general; soil conditions and calibration can affect the relationship between a reading and the conditions at a particular site.
The sensors do not support measurement averaging. Readings outside the standard measurement range, or sudden shifts in readings, can be useful diagnostic clues. They may indicate poor soil contact, nearby foreign material, soil settling, or a change to the installation.
Compare probe options and measurement limits
The two models use different ECH2O probes and have different measurement characteristics. Both operate at 70 MHz, use one data channel, and have an accurate soil measurement temperature range of 0°C to 50°C. Although the probe and cable can safely tolerate temperatures as low as -40°C, measurements at those extremes are outside the accurate range. The electronics tube can be exposed to temperatures up to 70°C, but readings beyond the specified soil range should not be treated as accurate.
- S-SMC-M005: Uses the EC-5 probe. Its standard in-soil range is 0 to 0.550 m³/m³, resolution is 0.0007 m³/m³, and volume of influence is 0.3 liters. Typical system accuracy is ±0.031 m³/m³ for mineral soils up to 8 dS/m; with soil-specific calibration, accuracy is ±0.020 m³/m³.
- S-SMD-M005: Uses the 10HS probe. Its standard in-soil range is 0 to 0.570 m³/m³, resolution is 0.0008 m³/m³, and volume of influence is 1 liter. Typical system accuracy is ±0.033 m³/m³ for mineral soils up to 10 dS/m; with soil-specific calibration, accuracy is ±0.020 m³/m³.
Both models provide extended readings beyond their standard VWC ranges. These values can help diagnose installation or sensor operation, but they are not part of the stated standard in-soil measurement range. The S-SMD-M005 also uses more battery power than other models. With H21-00x loggers powered by four AA batteries, no more than six of these sensors should be connected if maintaining a one-year battery life is required. This model requires HOBOware version 3.2.1 or later.
Installation practices for dependable readings
The probe measures water content in the soil immediately next to its surface, making installation quality critical. Air gaps, excessive compaction, or material caught between the probe prongs can influence the result. Install the probe in undisturbed soil with good contact, avoiding pebbles, roots, sticks, and bark where possible. Apply care in dense soil: excessive sideways force can break the prongs.
Keep the probe at least 8 cm (3 inches) from other objects, particularly large metal items. Objects in this area can affect the probe’s electromagnetic field. The S-SMC-M005 should be installed at least 3 cm from the soil surface; the S-SMD-M005 requires at least 10 cm.
A practical installation sequence is to make a hole to the desired depth, then press the probe into undisturbed soil at the bottom or side. An angled hole can be useful. A slotted PVC pipe can help guide the probe and cable during insertion. Partially backfill the hole, water the surrounding soil to help it settle, and complete the backfill while matching the density of the undisturbed soil as closely as possible. Secure the cable, protect it with conduit where exposure to animals, machinery, or chemicals is a concern, and never pull the probe from the soil by its cable.
For long-term protection, mount the smart sensor adapter horizontally and route the wires with drip loops so water drains away from the cable entry. The housing is weatherproof when mounted properly, but it is not waterproof.
Calibration, interference, and logger setup
The sensors are pre-calibrated for most soil types. High sand or salt content can make the standard calibration inaccurate, so teams working in these soils may need a soil-specific calibration. Collecting soil samples from each measurement depth during installation can support that work. The stated soil-specific accuracy is ±0.020 m³/m³.
Radio-frequency interference is another consideration. The sensing design is susceptible to RF signals, and exposure to strong electric fields can reduce accuracy. The stated impact differs by model: the S-SMC-M005 accuracy specification is reduced to 0.061 m³/m³ under certain RFI environments, while the S-SMD-M005 specification may be significantly reduced. Deployment changes and RFI mitigation practices may help, but can also result in reduced system accuracy. On-site testing is recommended for planned S-SMD-M005 deployments in high-RFI environments.
To connect a sensor, stop the logger and plug its modular jack into an available port. A 1-to-2 adapter can connect two sensors through one port if needed. The logger detects the sensor when next used. Each sensor occupies one data channel; a compatible logger supports up to 15 channels and up to 100 m of smart sensor cable.
Turn measurements into useful field data
These sensors offer a straightforward way to collect soil VWC data, but trustworthy monitoring starts with matching the probe to the application and installing it carefully. Keep operating temperatures and interference in view, investigate unusual readings rather than assuming they reflect soil conditions, and use soil-specific calibration when the soil demands it. With those practices in place, the logger’s direct VWC output can support consistent observation of changing soil moisture conditions.
Access Official Technical PDF