FPGA-based mobile robot navigation brings sensor processing and motion control into configurable hardware designed to respond in real time. A prototype developed for educational and research use combines camera-based line tracking with ultrasonic obstacle detection, using VHDL logic to coordinate sensing and movement. Its architecture offers a practical example for automation engineers and system integrators exploring how an FPGA can manage several robot functions without a separate processor.
FPGA-based mobile robot navigation architecture
The system uses a Xilinx Artix-7 FPGA on a Nexys 4 development board operating at 100 MHz. A front-facing camera provides image data for line tracking, while three ultrasonic sensors measure distances to obstacles. Two DC motors drive the robot’s wheels through an H-bridge, and a battery supplies power to the board and motors.
Rather than placing navigation decisions in a general-purpose processor, the design implements its processing and control blocks in VHDL. The FPGA architecture includes camera and image-capture functions, memory for captured image data, a black-and-white filter, line-tracking logic, ultrasonic sensor drivers, and a motor driver. The camera image can also be sent to a VGA display for viewing.
This organization separates the main tasks into functional blocks while keeping them within one programmable device. It is useful as a learning platform for understanding how sensor inputs, image processing, decision logic, and actuator outputs fit together in an embedded control system.
Ultrasonic sensing for obstacle avoidance
Three HC-SR04 ultrasonic sensors are mounted at the front of the robot and oriented at different angles. Each sensor estimates the distance to an object by measuring the time between transmitting an ultrasonic wave and receiving its echo. The distance calculation is based on the sound’s travel time and speed, with the measured round trip divided by two.
The controller compares each measured distance with a threshold selected through testing. A reading below that threshold indicates that the robot should respond to an obstacle. It then compares the distances reported by the sensors to choose a direction: when the left side appears clearer than the right, the robot turns left to move away from an object on its right.
If all three sensors report distances below the threshold, the control logic commands a half-turn to help the robot avoid remaining blocked. This approach relies on directional distance measurements rather than a detailed map of the surroundings. For engineers, the key design point is that sensor placement and threshold selection directly inform the navigation behavior.
Camera-based line tracking with a binary image model
For line tracking, the camera observes a white line on a black background. The image is converted to black and white using a threshold: sampled pixels above the threshold are represented as white, while the others are represented as black. The threshold was adjusted through tests for the prototype.
The controller samples 11 horizontally aligned points across the image, spaced 44 pixels apart. It represents their filtered values as an 11-bit vector. The three central bits are used to identify the line: when they are all zero, the system considers the line detected. The position of the zero-valued region across the wider vector then guides the steering decision.
The motor-control table maps different vector patterns to left, forward, or right movement, with PWM duty cycles selected for those actions. Patterns indicating the line toward one side produce a turn in that direction; central patterns command forward motion. If the robot loses the line while negotiating a bend, the described system stops.
VHDL motor control and PWM drive
The FPGA controls the DC motors through an H-bridge. Direction inputs determine motor rotation, while enable inputs receive pulse-width modulation (PWM) signals to regulate speed. PWM controls the proportion of time that a signal is active during each cycle, allowing the controller to vary the motor drive without changing the FPGA’s operating clock.
In this design, the duty cycle is selected according to the line-tracking pattern and steering action. The motor driver also receives navigation decisions from the obstacle-avoidance logic. As a result, image-based steering and ultrasonic responses use the same hardware path to influence the robot’s movement.
Implementation considerations for embedded control
The system was synthesized for the Artix-7 device using Vivado 2018.2. The reported resource use shows 1,107 LUTs out of 63,400 and 481 flip-flops out of 126,800. Block RAM use was 104 of 135 available blocks, or 77.04% of the reported capacity. The design did not require a processor or external RAM resources.
That block RAM figure is worth considering when adapting the architecture. Image capture and processing make memory a significant part of the implementation, even though other listed logic resources were used at lower proportions. The camera specified for the prototype provides VGA images at 640 by 480 pixels, with a maximum rate of 30 frames per second. System designers should account for the memory and I/O requirements of their own camera and processing choices rather than treating the control logic as the only resource constraint.
Practical implications for automation teams
This prototype demonstrates one way to combine line following and obstacle response in an FPGA-based embedded system. Its practical lessons include:
- Partition functions clearly: Separate sensor drivers, image processing, navigation decisions, and motor control into identifiable logic blocks.
- Connect sensing to action: Define how camera patterns and distance thresholds translate into steering, stopping, or turning behavior.
- Check resource budgets: Review memory, I/O, and logic use early, particularly when image data is involved.
- Validate thresholds and patterns: The line filter threshold and obstacle distance threshold were adjusted through testing, so these values are part of the control design.
For industrial automation engineers, system integrators, and technical educators, the central takeaway is that FPGA-based mobile robot navigation can bring camera processing, ultrasonic sensing, and PWM motor control into a single VHDL implementation. The prototype is an educational platform rather than a claim of deployment-ready performance, but its modular architecture provides a concrete basis for studying real-time embedded control and extending navigation functions.
Access Official Technical PDF