Effective asset tracking depends on more than obtaining a location. Device configuration determines when a tracker reports, which positioning method it uses and how operators interpret the resulting data. SimplePack Plus and Xsense illustrate two approaches: Wi-Fi-based geolocation for SimplePack Plus, and GPS with Wi-Fi fallback for Xsense. Both combine location reporting with movement logic and a platform for reviewing tracker status and history.
For automation engineers, integrators and operations teams, these details matter when selecting a tracking mode and setting expectations for coverage, reporting frequency and battery behavior.
Asset tracking methods: GPS and Wi-Fi positioning
GPS can provide outdoor coordinates, while Wi-Fi positioning can help estimate location by identifying nearby access points. The devices described use different combinations of these methods:
- SimplePack Plus 3.0 Full: scans nearby Wi-Fi access points and sends up to three MAC addresses to the Zenzi platform through Sigfox messages. The platform translates the reported MAC addresses into latitude and longitude. At least two MAC addresses are required for this translation, and precision depends on how many access points are available nearby.
- Xsense: prioritizes GPS and allows up to 60 seconds to capture coordinates. If GPS is unavailable, it scans for nearby Wi-Fi access points and sends up to two MAC addresses. The platform can use at least two MAC addresses to translate Wi-Fi observations into coordinates.
Xsense can also use BLE beacon information for indoor geolocation, according to its device description. In practice, the available positioning method and nearby signals shape what location information the system can report.
Movement logic controls when devices report
Accelerometer-based logic can help distinguish stationary periods from movement. SimplePack Plus sends a start-of-movement message when movement is detected, then sends periodic updates every three minutes while movement continues. After ten minutes without detected movement—the stated default—it sends a stop-of-movement message.
Xsense applies additional rules to location reporting. After the device is turned on and movement is detected, it sends a location message using GPS when available or Wi-Fi observations otherwise. The accelerometer then inhibits further operation for three minutes, regardless of whether movement continues. This inhibit period is a configuration setting, not a guarantee of a location message every three minutes.
During movement, Xsense sends another location message when the reported position is beyond the configured GPS inhibit distance of 25 metres, or when the Wi-Fi MAC addresses differ from the previous reading. It does not send a message when the location remains within that distance or the reported Wi-Fi MAC addresses are unchanged. The configured GPS report interval is also three minutes. These rules reduce redundant reporting while allowing location changes to be captured according to the device settings.
Use the platform to interpret tracker status
The Zenzi platform presents tracker information in map and list views. The main dashboard shows tracker locations on a map and provides a list with each device’s name, tracking technology, battery level and last-seen date and time. Users can open a tracker’s location history from the list and view its last known position on a full-screen map.
For an individual tracker, the detail dashboard provides location history over a selected time range. Operators can review the last ten locations, navigate between them and inspect a marker for location details and its timestamp. A red line displays the reported route within the selected time window. Location history can also be exported in XLS or CSV format.
Geofencing adds an operational alert layer. Where zones have been defined, the platform can trigger an alarm when a device leaves its assigned zone. The alarm view lists active alarms; the described controls allow users to acknowledge or clear them. Alarm visibility and available platform functions can depend on account permissions.
Configuration and battery considerations
Xsense settings include a daily heartbeat interval, GPS reporting and inhibit parameters, a five-satellite requirement and a button that can turn the device on or off. Its temperature, humidity, pressure and reed-switch sensors are disabled in the configuration described. This is a useful reminder that device capabilities and enabled functions are not necessarily the same: integrators should verify the intended configuration before deployment.
Battery level also affects operational planning. The supplied SimplePack Plus ranges describe full power from 3.1 V to 2.8 V, full power with medium range from 2.8 V to 2.4 V, weaker transmission range from 2.4 V to 2.3 V, and device shutdown below 2.3 V. For Xsense, the stated full-power level is 3.64 V and the device stops working at 2.74 V, with 14 levels in between. These device-specific thresholds should not be treated as interchangeable.
Xsense is rechargeable by Micro USB, and the device information notes that operating conditions, including extreme temperatures, affect performance and battery life. Reporting frequency and tracking mode should therefore be considered alongside charging access and the required level of location detail.
Match tracking behavior to the operation
A practical deployment begins by defining what the operation needs to know: a route, a general location, or a movement or boundary event. Route-oriented tracking involves repeated location reports; locating mode can focus on where an asset is without necessarily recording its full route; and button-based operation can request a location when needed. Xsense descriptions also identify potential configurations for cold-room monitoring, ambient conditions and door status, though the sensors must be enabled and configured for those uses.
Before rollout, confirm the positioning priority, reporting intervals, movement thresholds, geofence setup, enabled sensors and battery requirements. Test how the chosen device behaves in the actual environment, particularly where GPS or nearby Wi-Fi access points may not be available. Clear configuration and realistic expectations help operations teams make better use of location history and alerts.
Conclusion
Asset tracking with SimplePack Plus and Xsense combines positioning technology, movement rules and platform tools. GPS and Wi-Fi offer different ways to derive location, while accelerometer logic and distance or signal comparisons determine when updates are sent. For industrial teams, the practical priority is aligning those settings with the task—then using tracker status, history and geofence alarms to support day-to-day visibility.
Access Official Technical PDF